Smeg WATER CIRCUIT EMPTY: air in the built-in's water line
If the tank runs dry or comes out while the machine is working, the pump can pull in air.
Mon–Sat, 8am–8pm
- Water and tank
- Coffee machine pump repair
- Source: Smeg
Book a visit
Three short steps, about a minute.
or call (844) 551-4777
Loading appointment form…
The appointment form couldn’t load. Please try again.
What WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS
actually means.
If the tank runs dry or comes out while the machine is working, the pump can pull in air. The Smeg built-in then shows WATER CIRCUIT EMPTY and refills the line by running water from the spout.
Smeg coffee machine display · also shown as WATER CIRCUIT EMPTY
What to do when WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS shows on the coffee machineKind of codeWater and tank
The machine asked for water and did not get what it expected: the tank is empty, sits off its seat or has a float the sensor cannot see, air is trapped in the line, or the flowmeter counted too little water passing in the time allowed. On a plumbed unit the same message can mean a closed shutoff, a kinked supply hose or a clogged inlet valve. Reseating a full tank and running a rinse clears the simple cases; a pump that hums with nothing moving is a visit.
Usually leads toCoffee machine pump repair
Testing and replacing the pump that drives water through the coffee, with the flowmeter that counts each cup and the valves beside it.
Shows up asWhat a Coffee Machine Error Code or Warning Symbol Means
A coffee machine error code may show as a short string of letters and numbers, a flashing symbol for water, grounds or the brew unit, a short sentence on a text display, or a machine that stops with one light blinking.
MakeSmeg
A Smeg espresso machine is repaired at the owner's kitchen counter after a single test shot shows where the trouble begins.
SourceSmeg automatic built-in coffee machine instruction manual (linked from the US CMSU4303X, CMSU4104S and CMSU2104G pages)
Smeg US built-in automatic coffee machines CMSU4303X (Classic, listed as retiring), CMSU4104S and CMSU2104G (Linea). All three link the same instruction manual, and the message appears on the full-touch display in capitals.
Before you book,
in this order.
Each step comes from Smeg's own guidance for WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS on its coffee machines. Follow it to the end: the last card says whether this is a visit.
Make sure the tank is full and latched.
Fit the hot water spout, hold a cup under it and confirm; the flow stops on its own when the circuit is full.
Book a visit if the message returns every time, since the pump may not be drawing from the tank.
Still there?
It usually turns into coffee machine pump repair. Book with the code and the model number.
What not to do
It is a priming step, not a leak. The tank-level prompt is a separate message and asks only for water in the tank.
What you may
notice with it.
The coffee machine problems WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS tends to arrive with. Answer these at the coffee machine before anyone is booked.
All problems
Where WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS usually leads
Coffee machine pump repair.
Smeg
coffee machines.
A Smeg espresso machine is repaired at the owner's kitchen counter after a single test shot shows where the trouble begins.
Smeg coffee machine repairMore Smeg codes
Water and tank on other makes
Built-in coffee system
The coffee machine set flush into a tall kitchen cabinet, filled from a water tank behind its front, grinding beans and brewing each cup on its own before sliding out on rails for service.
Countertop espresso machine
The fully automatic bean-to-cup machine that stands on the counter, grinding, tamping, brewing and frothing at the touch of a key, with its tank, hopper and grounds drawer all reached from the top and the front.
Manual espresso machine
The home espresso machine with a portafilter you fill and lock in by hand, a pump and a boiler or thermoblock inside, and a steam wand for milk you froth yourself.
In Smeg's own words
The water circuit is empty
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Smeg US built-in automatic coffee machines CMSU4303X (Classic, listed as retiring), CMSU4104S and CMSU2104G (Linea). All three link the same instruction manual, and the message appears on the full-touch display in capitals.
Smeg WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS coffee machine repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS.
Can I clear WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS myself?
Why does my Smeg show WATER CIRCUIT EMPTY after sitting unused?
Is it safe to run the prime on a Smeg built-in myself?
Why is my Smeg pump loud when this message shows?
Back to your everyday
Still showing WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS?
Three things make the booking useful: the message or number exactly as the display showed it, the full model number from the plate, and whether the machine still grinds and pours at all. Send those and the likely part can be looked up before the van leaves.